Eucatex


  • Eucatex Soft Touch Premium Satin Acrylic



The colors and patterns on this site are only for reference, there may be divergence between the colors on the screen and the real colors of products. Availability on request.

Eucatex Soft Touch Premium Satin Acrylic has high performance for people seeking higher performance, durability and yield in painting external and internal areas. A product easy to apply, with excellent coverage, little splashing, excellent washability, it removes dirt very easily, has excellent spreading and extremely good finishing. Its smooth perfume lasts approximately 24h and, at the end of this period, disappears. It is indicated for painting external and internal surfaces of plaster, acrylic putty, textures, concrete, fiber cement, repainting on PVA and acrylic and internal surfaces covered with putty and gypsum.

Composition

Resin with a base of aqueous dispersion of acrylic styrene copolymer, pigments free of heavy metals, inert mineral loads, glycols and tensoactives.

This product is classified as per standard NBR 11.702 of the ABNT. Type 4.5.4

  with water m2/coat  
Masonryry 1st coat 20 to 30% – others 10 to 20% Spray Gun: dilute with 30% of water, pressure between 2.2 and 2.8 kgf/cm² or 30 to 35 lbs/in² 8 to 14
32 to 59
160 to 294
36 to 66
180 to 330

¼ gallon (0.800 ml)
Gallon (3.2 liters)
Can (16 liters)
Gallon (3.6 liters)
Can (18 Liters, 1.6 liters, 3.6 liters, 3.2 liters, 800 ml)


 
Usually from 2 to 3 coats are sufficient to attain the coverage desired, but, depending upon the type, state of the wall and color used, a greater number of coats may be required.

Drying Period:To touch: 2 hours
Between Coats: 4 hours
Final: 12 hours


Application
Wool roller Paintbrush or flat paintbrush Spray gun


Tips

  • Avoid applying the product on rainy days, or with a temperature below 10ºC or above 40ºC and relative air moisture exceeding 90%;
  • Up to 20 days after the painting, isolated raindrops may cause stains. If this occurs,  immediately wash up  surface with clean running water, without rubbing (to avoid wear, aggression of the film or emphasizing the gloss);
  • We do not recommend the use combined, or mixed, with other products not specified on this packaging.


Recommendations

  • In certain situations, depending upon the luminosity of the room and the condition of the  substrate  semi-gloss and satin products may reveal defects and imperfections of the surface more sharply than other finishings. This is due to the reflection of the light, which is a feature of these products. In these cases, it is advisable to use Eucatex Premium Matt Acrylic, as, among the acrylic finishings, it is the ideal product to conceal small defects of the surface as undulations and imperfections of the substrate:
  • To obtain a fine finishing on putty spackle or acrylic coated surfaces, we recommend using a wool roller with little thickness, the same as used for applying epoxy paint;
  • In painting or repainting where there are applications or touch-ups of putty( Acrylic or Gypsum), differences of gloss can be noted after the application. This is due to the lack of uniform absorption of the substrate To avoid this effect, we recommend applying the paint itself diluted with 30% of water only at the points which’ putty corrections have been made;
  • Removal of dirt: in the place affected, use a soft sponge or cloth with neutral detergent. Then, clean with a moistened cloth. Perform the cleaning with smooth movements, only in the place affected, to preserve the original finishing. In the case of deeper dirt, this process may cause  polishing of the paint film (difference of gloss), but does not affect its resistance and durability;
  • Avoid isolated touch-ups after the paint has dried;
  • The practical yield can vary due to the method of application, geometry of the structure, rugosity and absorption of the surface, thickness of the product layer deposited, atmospheric conditions and application technique;
  • In certain situations, depending upon the conditions of the ambience, as size of the area, ventilation, air moisture and temperature, the slight  scent may take longer than 24h to dissipate.


Classification

Product classified according to  Standard NBR 11702 of the ABNT, type 4.5.4 Product in compliance with standard NBR 15079 of May 2011 of the ABNT. The warranty is provided so long as  the user follows all the instructions of preparing the surface, dilution and application of the product and also keeps the document and manufacturing batch number #. The warranty is restricted to replacing the product.


Safety

  • Maintain the packaging well closed, always in the vertical position, in a covered, fresh and ventilated place, far from sources of heat and humidity. Do not perforate or burn it and do not reuse it for other purposes. Keep it out of the reach of children and animals. Do not put it in contact with food and water to be consumed;
  • During the preparation, application and drying of the product, maintain the room ventilated, wear a protective mask, gloves and appropriate safety goggles;
  • In cases of accidental contact with the skin, wash it with clean water and soap; in the case of the eyes, wash them with clean running water for at least 15 minutes. If there is accidental inhalation of the product vapors, take the person to a ventilated place. Do not swallow the product. If this occurs, do not cause vomiting. People with a history of allergy to the product must avoid handling it. For further information, see the Chemical Product Safety Sheet – FISPQ, available on site www.eucatex.com.br. If the aforementioned situations are serious, seek medical aid and take with you this packaging or contact CEATOX – Toxicological Assistance Center (24 hours), telephones: 0800-0148110 or (11) 2661-8800.

According to  standard ABNT NBR 13.245.

  • The surface must be firm, cohesive, clean, dry, without dust, fatty materials, soap and mould;
  • Surfaces with loose flakes or coated on whitewash (lime ): they must be scraped off or brushed off until the complete removal of the paint residue. Then apply the Eucatex Wall-Preparing Undercoat, as recommended  on the packaging;
  • Mould surfaces: wash them with a solution of water mixed with sanitary water in the proportion of 1:1, rinse them and wait for them to dry (the possible causes of the mould must be corrected);
  • Surfaces with fatty stains: wash them with a solution of water and neutral detergent, rinse them and wait for them to dry;
  • New plaster: wait for the cure for at least 30 days. Apply 1 or 2 coats of Eucatex Acrylic Sealer, as per the recommendation of the packaging. If necessary level the surface applying 2 or 3 coats of Eucatex Acrylic Putty (wet areas) or Eucatex Putty (areas not wet );
  • Weak plaster (low cohesion): apply Eucatex Wall-Preparing Undercoat as recommended on the packaging and level the surface, applying 2 or 3 coats of Eucatex Acrylic Putty (wet areas) or Eucatex Putty (areas not wet).
 

Consejos

  • Evite la aplicación del producto en días lluviosos, temperatura abajo de 10ºC o superiores a 40ºC y humedad relativa del aire superior a 90%;
  • Conservarlos por 20 días después de haber realizado la pintura, las gotas de lluvia pueden provocar manchas. Si eso se produce, lavarlas de inmediato toda la superficie con agua limpia sin frotarlas ( para evitar el desgaste, agresión de la película o levantamiento del brillo);
  • No recomendamos el uso combinado mezclado con otros productos no especificados en el embalaje.
 

Recomendaciones

  • En determinadas situaciones, dependiendo de la luminosidad del ambiente y de la condición del substrato, productos semibrillantes y satinados pueden revelar defectos e imperfecciones de la superficie de forma más acentuada que otros acabados. Eso se debe al reflejo de la luz, que es una característica de estos productos. En estos casos, recomendase el uso de Eucatex Acrílico opaco Premium, porque, entre los acabados acrílicos, es el producto ideal para disfrazar pequeños defectos de la superficie como ondulaciones e imperfecciones del substrato;
  • Para poder obtener un buen acabado sobre el enduido plástico o acrílico, recomendamos hacer uso de un rodillo de lana  de pelo bajo, el mismo que es usado para la aplicación de tinta epoxi;
  • En pinturas o repinturas donde existen aplicaciones o retoques de masillas (plásticas, acrílicas o yeso), pueden ser vistas las diferencias de brillo tras su aplicación. Eso se debe a la falta de absorción uniforme del substrato. Para evitar ese efecto, recomendamos la aplicación de la propia tinta diluida con 30% de agua solamente en los puntos donde fueron hechas las correcciones con masillas.
  •  Retirada de suciedad: en el local afectado, usar un paño o esponja suave con detergente neutro. Enseguida, limpiarlo con un paño humedecido. Realizar la limpieza haciendo  movimientos suaves, solamente, en el local afectado, para conservar el acabado original. En caso de suciedades más profundas, ese proceso podrá genera un pulimento de la película de tinta (diferencia de brillo), pero que no afectará su resistencia y durabilidad.
  • Evitar de hacer retoques aislados después del secado de la tinta;
  • El rendimiento práctico puede variar de acuerdo al método de aplicación, geometría de la estructura, rugosidad y absorción de la superficie, espesura de la capa del producto depositada, condiciones atmosféricas y técnica de aplicación.
  • En algunas situaciones, dependiendo de las condiciones del ambiente, el tamaño del área, ventilación, humedad del aire y temperatura, el suave perfume para disiparse podrá tardar un tiempo mayor que 24h.
 

Clasificación

Producto clasificado conforme la Norma NBR 11702 de la ABNT, tipo 4.5.4 Producto que esta de acuerdo con la Norma NBR 15079 de mayo de 2011 de la ABNT. Los términos de garantía esta constituida desde que el usuario siga todas las instrucciones de preparación de la superficie, dilución y aplicación del producto y tenga en su poder l factura y el Nº del lote de fabricación. Así mismo, la garantía restringe la reposición del producto.
Seguridad
  • Conservar el embalaje bien cerrado, siempre en la posición vertical, en local cubierto, fresco, ventilado, lejos de las fuentes de calor y humedad. Evite de perforar, quemar y de reutilizar para otros fines. Mantenga el producto fuera del alcance de los niños y animales. Evite de poner en contacto con los alimentos y agua de consumo;
  • Durante la preparación, aplicación y secado del producto, mantenga el ambiente ventilado, recomendase usar una máscara protectora, guantes y lentes de seguridad apropiados;
  • En casos de contacto accidental con la piel, lavar con agua limpia y jabón; en caso de los ojos, lavarlos con agua con abundancia por lo menos durante 15 minutos. En caso de que haya una inhalación accidental de los vapores del producto, llevar la persona para el local ventilado. No ingerir el producto. En caso de que se produzca, evite de provocar el  vómito. Personas con historial de alergia al producto deben evitar su manoseo. Para mayores informaciones, consultar la Ficha de Seguridad del Producto Químico – FISPQ, disponible en el sitio: www.eucatex.com.br. En caso de problemas graves de las situaciones arriba citadas, buscar ayuda médica y llevar consigo éste embalaje o entrar en contacto con el CEATOX – Centro de Asistencia Toxicológica (24 horas), a través de los teléfonos: 0800-0148110 ó (11) 2661-8800.